您好, 歡迎來到化工儀器網
產品分類品牌分類
-
IFM變送器 IFM斷路器 IFM解調器 IFM攝像機 IFM控制器 IFM電纜 IFM壓力變送器 IFM超聲波流量傳感器 IFM壓縮空氣流量計 IFM振動變送器 IFM加速計 IFM振動傳感器 IFM標簽 IFM閱讀器 IFM讀寫頭 IFM主機 IFM網關 IFM旋入式傳感器 IFM液位傳感器 IFM控制面板 IFM流量計 IFM流量變送器 IFM超聲波流量計 IFM渦街流量計 IFM電磁流量計 IFM壓力計 IFM壓力傳感器 IFM控制閥 IFM安全光柵 IFM安全光幕 IFM3D攝像機 IFM傳感器 IFM3D傳感器 IFM開關 IFM模塊 IFM分配器 IFM延伸器 IFM轉換器 IFM繼電器 IFM顯示器 IFM速度監控器 IFM編碼器 IFM放大器 IFM觸摸式傳感器 IFM對比傳感器 IFM彩色傳感器 IFM光纖放大器 IFM激光傳感器 IFM光電式傳感器 IFM溫度傳感器 IFM氣缸傳感器 IFM速度傳感器 IFM磁性傳感器 IFM電容式傳感器 IFM電感式傳感器 IFM位置傳感器 IFM傾角傳感器
-
賀德克HYDAC液壓閥 賀德克HYDAC蓄能器 賀德克HYDAC流量變送器 賀德克HYDAC壓力表開關 賀德克HYDAC過濾裝置 賀德克HYDAC熱交換器 賀德克HYDAC距離傳感器 賀德克HYDAC壓力閥 賀德克HYDAC冷卻器 賀德克HYDAC電磁閥 賀德克HYDAC繼電器 賀德克HYDAC換向閥 賀德克HYDAC壓力傳感器 賀德克HYDAC同軸閥 賀德克HYDAC截止閥 賀德克HYDAC球閥 賀德克HYDAC油況傳感器 賀德克HYDAC污染傳感器 賀德克HYDAC轉速傳感器 賀德克HYDAC位置傳感器 賀德克HYDAC位置開關 賀德克HYDAC液位傳感器 賀德克HYDAC液位開關 賀德克HYDAC流量開關 賀德克HYDAC流量傳感器 賀德克HYDAC溫度開關 賀德克HYDAC溫度傳感器 賀德克HYDAC壓力開關 賀德克HYDAC測量儀 賀德克HYDAC壓力變送器 賀德克HYDAC葉片泵 賀德克HYDAC濾筒 賀德克HYDAC比例閥 賀德克HYDAC止回閥 賀德克HYDAC節流閥 賀德克HYDAC限壓閥 賀德克HYDAC方向閥 賀德克HYDAC阻尼器 賀德克HYDAC活塞式蓄能器 賀德克HYDAC監控系統 賀德克HYDAC過濾器 賀德克HYDAC濾清器 賀德克HYDAC濾芯
BRAUN傳感器A5S0DD0具體參數表
Differential-Hall-Effect based Sensors for Detection of Speed in Non Hazardous Areas Series A5S0DD0 / A5S0DS0 The BRAUN Speed Sensors Series A5S are TÜV certified for SIL3 acc. IEC 61508:2010 and therefore meet the high SIL3 standards. The correct choice of sensor is always a prerequisite to achieving a successful solution. Therefore BRAUN A5S0 sensors base on the proven Differential-Hall-Effect principle. Their low end of 0 Hz allows monitoring the machine down to zero speed. They are contact-free, wear-free, maintenance-free and unsusceptible versus external magnetic stray fields and machine vibration. These characteristics make the series of A5S0 sensors especially suited for all applications where high levels of accuracy and reliability are at a premium. In contrast, other sensors like magnet-inductive or static Hall-sensors do not meet these demands. Each sensor in the series is available in various lengths and diameters and comes with a choice of connections. However, functionally all sensors have the same characteristics. The stainless steel sensor housing is sealed at the front and is pressure resistant (> 200 bars). A flat shaft is available or with a screw-in thread M12x1, M14x1, M14x1,5, M16x1, M16x1,5, M18x1, M18x1,5, M22x1, 5/8-18UNF-2A. Customized dimensions and thread specifications are possible. To meet the specific requirements of hazardous areas we provide specialized types which are certified for ATEX/IECEx, as well as for other international standards such as UL/CSA and EAC (the Eurasian Customs Union with Russia, Kazakhstan, and Belarus). For Ex Zone 0 or 1 we provide an intrinsically safe implementation in conjunction with our Barrier D461, for Ex Zone 2 a non-sparking (non-incendive) variation is available. A5S0 sensors – the best choice for demanding applications KEY FEATURES SIL3/IEC 61508:2010 certified by TÜV Detection of rotational speed in non hazardous areas Speed range from 0 Hz to 25 kHz Air gap to the target / pole wheel up to 2.5 mm (depending on the profile size) Temperature range -40…+125 °C (-40…+255 °F) Differential principle diminishes the influence of external magnetic stray fields and of machine vibration Sealed stainless steel enclosure > 200 bar pressure to the sensor tip Available for connection via tight plug, or with firmly attached cable (PVC or Teflon® insulated) Powerful square wave output signal equally high over the entire speed range Sensor short circuit proof and protected versus polarity error Accepting fine and coarse profiles, as gear wheels, slots, cams, holes in any ferrous material BENEFITS Contact-free with a large air gap, so the potential for damage is eliminated Wear-free due to its unique design principle Maintenance-free during Lifetime, therefore minimized TCO Unsusceptible versus external magnetic stray fields and machine vibration Operates down to zero speed Can not be damaged by faulty wiring Almost every target profile can be used A5S0 Sensors do not influence